Home > Drivers Para > Drivers Para Cable Dcu-65

Drivers Para Cable Dcu-65

If you hold the button too long Arduino will eventually give up and report that the programmer is unavailable. February 21, 2010 Filed under: Electronics -- jethomson @ 5:25 am Please take a moment to vote for my entries in the Hack It! Reply Bubbles Says: February 27, 2010 at 12:37 am Came in through hackaday. Looks like I will have to crack open the case and run my own wires! this content

I also had two additional wires, one green (pin 3), one red (pin 4). They're available on eBay and DealExtreme and very inexpensive. I was planning on doing this for my mythbox, but didn't have to when I got a nice remote from someone with a Windows MCE PC that wasn't using it. I did a quick probe to confirms this, then attempted to solder the green wire to the via.

For my cable pin 6 was white, pin 7 was blue, and pin 8 was black. I already have one of the modern device BUB programmers, and it works a charm. Just search for PL2303 or CP2102. The picture below shows the location of the USB VCC pad and a via that connects to pin 2 of the PL-2303HX (pin name DTR_N).

Victor Says: March 18, 2010 at 2:03 am Just an update on the pin 2 - it isn't DTR, at least I don't think it is. Choose "No, not this time" and push "Next >" button. 6. It was a bit of a headache. Any other locations where the prog can be found?

I documented it on my blog and gave you credit: http://captainsolderburn.wordpress.com/2010/05/16/boarduino-and-serial-cable/ Reply Dan Says: May 19, 2010 at 6:23 pm There is a eeprom attached to the PL-2303 that controls several Now we're ready to try uploading. The typical/max operating current required by the PL-2303HX is 20/25 mA. https://docs.google.com/document/d/17zVUklkNsxJljP_sHOhYyh_GCQv1DGk7M9N-Q6dmY6g Plug in the cable, power on the device, and start the Arduino IDE.

When i connect the Rx/Tx wires and in hyperterminal whatever i typed i get on the window with no garbage… can you help me.. This article will focus on the CA-42 containing a PL2303HX rev. Both were physically moleded around the circuit board so I managed to break the wires. Thanks jethomson Says: September 14, 2010 at 12:10 am I've replied to your post on edaboard.

I took those with a Canon P&S, a Powershot A75. https://www.amazon.com/Original-Sony-Ericsson-Cable-DCU-65/dp/B004KSP2HO There are slightly cheaper alternatives, but a real scrooge googles on. Any ideas? Connect your phone with keep pressed C to the cable. 5.

Reply Khalid Khattak Says: March 2, 2011 at 8:12 am Hi again, The CA-45 cable has some problems.. news Aaron Says: April 18, 2011 at 8:55 am Ray: I love big hard drives…dig around enough and you can find the cruft of ages. (or at least, a few months ago.) I have tried flow control settings, but doesn't seem to be the issue. To do this… …in Linux, use the command ‘ls /dev/ttyUSB*' before and after you plug in the cable.

To do this cut the cable a couple of inches (5 cm) from the phone connector. Using with Arduino Once you've tested your cable you can make it more permanent by adding crimp-on wire connectors with a 1×6 housing. NOTE: I said the phone connector not the USB connector. have a peek at these guys If you have a chip with a 5V tolerant RxD pin you'll get better performance if you leave out the voltage divider because of the inherent parasitics of the resistors.

Reply tantris Says: February 26, 2010 at 3:12 am A really thorough step-by-step writeup with good links. Just as I was considering cutting up a USB phone cable, I realised that I had a full-blown Linux system with a handily accessible serial port that runs at […] Reply Users of other operating systems may find drivers Prolific's site.

Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are

  • Strip the wires which correspond to pins 6, 7 and 8.
  • You should notice a new ttyUSB is added after you connect the cable. …in Windows, plug in the cable then open up the Device Manager by clicking Start->Run
  • Make sure none of the other wires are touching one another!
  • There was not enough slack in the wires to reach the new solder points so I removed a section of the cable's insulation below the strain relief and gently pulled a
  • The device manager recognised the device, Hyperterminal recognised the device as COM1, Arduino IDE also recognised the device… Hyperterminal window could not open the COM1, i changed the settings from COm1
  • Be aware that most setups put the reset capacitor on the board, so if you use your cable with one of these boards your total capacitance will be effectively halfed and
  • It looks like you added CTS too.
  • jethomson Says: April 23, 2010 at 9:08 pm Serial communication with RS232 is different from LVTTL.
  • for example typing M (sending to Arduino) will move the steppermotor 1step..The same way typing ‘S' will start the laser scanning process and typing ‘T' will off the laser, move the

and Make It Glow Challenges! Set your multimeter to measure voltage. People usually did it with a 3rd party chip. Make sure none of the wires are touching one another!

Any chance you could send the driver to me or post it somewhere? Further Modifications (Optional) Since these modifications depend heavily on the version of the PL-2303 used and the layout of it's PCB, this section should not be considered a guide on how When the "Connection Description" dialog comes up give it any name you like (e.g. check my blog For these penny pinching DIYers setting up an ATmega on a breadboard seems like the way to go until they discover the FTDI USB cable is $20.

According to pinouts.ru pin 5 is USB Vbus, which I call VCC in the article. تسجيل الدخول القائمة الرئيسية تسجيل الدخول القائمة الرئيسية One account. Precautions Never work on a live circuit!